| #################### This file is used by NXP NFC NCI HAL ##################### |
| ############################################################################### |
| # Application options |
| # Logging Levels |
| # NXPLOG_DEFAULT_LOGLEVEL 0x01 |
| # ANDROID_LOG_DEBUG 0x04 |
| # ANDROID_LOG_INFO 0x03 |
| # ANDROID_LOG_WARN 0x02 |
| # ANDROID_LOG_ERROR 0x01 |
| # ANDROID_LOG_SILENT 0x00 |
| NXPLOG_EXTNS_LOGLEVEL=0x04 |
| NXPLOG_NCIHAL_LOGLEVEL=0x04 |
| NXPLOG_NCIX_LOGLEVEL=0x04 |
| NXPLOG_NCIR_LOGLEVEL=0x04 |
| NXPLOG_FWDNLD_LOGLEVEL=0x04 |
| NXPLOG_TML_LOGLEVEL=0x04 |
| NFC_DEBUG_ENABLED=1 |
| |
| ############################################################################### |
| # Nfc Device Node name |
| NXP_NFC_DEV_NODE="/dev/nxp-nci" |
| |
| ############################################################################### |
| # Extension for Mifare reader enable |
| MIFARE_READER_ENABLE=0x01 |
| |
| ############################################################################### |
| # NXP proprietary settings |
| NXP_ACT_PROP_EXTN={2F, 02, 00} |
| |
| ############################################################################### |
| # NXP TVDD configurations settings |
| # Allow NFCC to configure External TVDD, two configurations (1 and 2) supported, |
| # out of them only one can be configured at a time. |
| #NXP_EXT_TVDD_CFG=0x02 |
| |
| ############################################################################### |
| #config1:SLALM, 3.3V for both RM and CM |
| #NXP_EXT_TVDD_CFG_1={20, 02, 0F, 01, A0, 0E, 0B, 31, 01, 01, 31, 00, 00, 00, 01, 00, D0, 0C} |
| |
| ############################################################################### |
| #config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM, |
| #monitoring 5V from DCDC, 3.3V for both RM and CM, DCDCWaitTime=4.2ms |
| #NXP_EXT_TVDD_CFG_2={20, 02, 0F, 01, A0, 0E, 0B, 11, 01, C2, B2, 00, B2, 1E, 1F, 00, D0, 0C} |
| |
| ############################################################################### |
| # Core configuration rf field filter settings to enable set to 01 to disable set |
| # to 00 last bit |
| #NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 00 } |
| |
| ############################################################################### |
| # To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set |
| # to 0x00 |
| #NXP_I2C_FRAGMENTATION_ENABLED=0x00 |
| |
| ############################################################################### |
| #set autonomous mode |
| # disable autonomous 0x00 |
| # enable autonomous 0x01 |
| NXP_AUTONOMOUS_ENABLE=0x00 |
| ############################################################################### |
| #set Guard Timer |
| # Guard Timer range to 0x0F-0xFF(i.e.15-255 seconds) |
| NXP_GUARD_TIMER_VALUE=0x0F |
| ############################################################################### |
| #Enable SWP full power mode when phone is power off |
| #NXP_SWP_FULL_PWR_ON=0x00 |
| |
| ################################################################################ |
| #This is used to configure UICC2 at boot time. |
| # UICC2 0x03 |
| NXP_DEFAULT_UICC2_SELECT=0x03 |
| |
| ############################################################################### |
| #SCR Read Tag Operation Timeout in secs |
| NXP_SWP_RD_TAG_OP_TIMEOUT=20 |
| |
| ############################################################################### |
| #Set the default route Location : |
| #This settings will be used when application does not set this parameter |
| # host 0x00 |
| # eSE 0xC0 |
| # UICC 0x80 |
| DEFAULT_ROUTE=0xC0 |
| |
| ############################################################################### |
| #Set the ISODEP (Mifare Desfire) route Location : |
| #This settings will be used when application does not set this parameter |
| # host 0x00 |
| # eSE 0xC0 |
| # UICC 0x80 |
| DEFAULT_ISODEP_ROUTE=0xC0 |
| |
| ############################################################################### |
| #Set the Default Off Host route Location : |
| #This settings will be used when application does not set this parameter |
| # host 0x00 |
| # eSE 0xC0 |
| # UICC 0x80 |
| DEFAULT_OFFHOST_ROUTE=0xC0 |
| |
| ############################################################################### |
| #Set the Felica CLT route Location : |
| #This settings will be used when application does not set this parameter |
| # eSE 0xC0 |
| # UICC 0x80 |
| DEFAULT_NFCF_ROUTE=0xC0 |
| |
| ############################################################################### |
| #Set the default AID Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Screen off unlock |
| # bit pos 4 = Screen On lock |
| # bit pos 5 = Screen Off lock |
| DEFAULT_AID_PWR_STATE=0x3B |
| ############################################################################### |
| #Set the Mifare Desfire Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Screen off unlock |
| # bit pos 4 = Screen On lock |
| # bit pos 5 = Screen Off lock |
| DEFAULT_DESFIRE_PWR_STATE=0x3B |
| |
| ############################################################################### |
| #Set the Mifare CLT Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Screen off unlock |
| # bit pos 4 = Screen On lock |
| # bit pos 5 = Screen Off lock |
| DEFAULT_MIFARE_CLT_PWR_STATE=0x3B |
| |
| ############################################################################### |
| #Set the Felica CLT Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Screen off unlock |
| # bit pos 4 = Screen On lock |
| # bit pos 5 = Screen Off lock |
| DEFAULT_FELICA_CLT_PWR_STATE=0x3B |
| |
| ############################################################################### |
| #Set the T4TNfcee AID Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Screen off unlock |
| # bit pos 4 = Screen On lock |
| # bit pos 5 = Screen Off lock |
| DEFAULT_T4TNFCEE_AID_POWER_STATE=0x3B |
| |
| ############################################################################### |
| #Set the default Felica T3T System Code OffHost route Location : |
| #This settings will be used when application does not set this parameter |
| # host 0x00 |
| # eSE 0xC0 |
| # UICC 0x80 |
| DEFAULT_SYS_CODE_ROUTE=0xC0 |
| ############################################################################### |
| # AID Matching platform options |
| # AID_MATCHING_L 0x01 |
| # AID_MATCHING_K 0x02 |
| #AID_MATCHING_PLATFORM=0x01 |
| |
| ############################################################################### |
| #CHINA_TIANJIN_RF_SETTING |
| #Enable 0x01 |
| #Disable 0x00 |
| #NXP_CHINA_TIANJIN_RF_ENABLED=0x01 |
| |
| ############################################################################### |
| #SWP_SWITCH_TIMEOUT_SETTING |
| # Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60]. |
| # Timeout in milliseconds, for example |
| # No Timeout 0x00 |
| # 10 millisecond timeout 0x0A |
| #NXP_SWP_SWITCH_TIMEOUT=0x0A |
| |
| ############################################################################### |
| # Flashing Options Configurations |
| # FLASH_UPPER_VERSION 0x01 |
| # FLASH_DIFFERENT_VERSION 0x02 |
| # FLASH_ALWAYS 0x03 |
| NXP_FLASH_CONFIG=0x02 |
| |
| ############################################################################### |
| # Bail out mode |
| # If set to 1, NFCC is using bail out mode for either Type A or Type B poll. |
| NFA_POLL_BAIL_OUT_MODE=0x01 |
| |
| ############################################################################### |
| # Allow list of Hosts |
| # This values will be the Hosts(NFCEEs) in the HCI Network. |
| DEVICE_HOST_ALLOW_LIST={02, 80, 81, C0} |
| |
| ############################################################################### |
| # Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1. |
| # 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm |
| # 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block |
| # 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check |
| # command is sent waiting for rsp and ntf. |
| PRESENCE_CHECK_ALGORITHM=2 |
| ############################################################################### |
| # Options to Fallback to alternative route |
| # Disable 0x00 |
| # DH 0x01 |
| # ESE 0x02 |
| NXP_CHECK_DEFAULT_PROTO_SE_ID=0x01 |
| ############################################################################### |
| # Vendor Specific Proprietary Protocol & Discovery Configuration |
| # Set to 0xFF if unsupported |
| # byte[0] NCI_PROTOCOL_18092_ACTIVE |
| # byte[1] NCI_PROTOCOL_B_PRIME |
| # byte[2] NCI_PROTOCOL_DUAL |
| # byte[3] NCI_PROTOCOL_15693 |
| # byte[4] NCI_PROTOCOL_KOVIO |
| # byte[5] NCI_PROTOCOL_MIFARE |
| # byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO |
| # byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME |
| # byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME |
| NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, FF, FF, FF} |
| |
| ############################################################################### |
| #NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE |
| #Enable/Disable block number checks for china transit use case |
| #Enable 0x01 |
| #Disable 0x00 |
| #NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE=0x01 |
| |
| ################################################################################ |
| #This flags will enable different modes of Lx Debug based on bits of the Byte0 |
| #Byte 0: |
| # |_________Bit Mask_______| Debug Mode |
| # b7|b6|b5|b4|b3|b2|b1|b0| |
| # | |x | | | | | | Modulation Detected Notification |
| # | | |X | | | | | Enable L1 Events (ISO14443-4, ISO18092) |
| # | | | |X | | | | Enable L2 Reader Events(ROW specific) |
| # | | | | |X | | | Enable Felica SystemCode |
| # | | | | | |X | | Enable Felica RF (all Felica CM events) |
| # | | | | | | |X | Enable L2 Events CE (ISO14443-3, RF Field ON/OFF) |
| #Byte 1: RFU, shall always be 0x00 |
| # Byte1 Byte0 |
| # \__ __/ |
| # e.g. NXP_CORE_PROP_SYSTEM_DEBUG=0x0031 ==> Modulation detected, L1, L2 CE |
| NXP_CORE_PROP_SYSTEM_DEBUG=0x0000 |
| |
| ############################################################################### |
| # Enable forward functionality |
| # Disable 0x00 |
| # Enable 0x01 |
| FORWARD_FUNCTIONALITY_ENABLE=0x01 |
| |
| ############################################################################### |
| # Configure the NFC Extras to open and use a static pipe. If the value is |
| # not set or set to 0, then the default is use a dynamic pipe based on a |
| # destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value |
| # for each EE (ESE/SIM1/SIM2) |
| OFF_HOST_ESE_PIPE_ID=0x16 |
| OFF_HOST_SIM_PIPE_ID=0x0A |
| OFF_HOST_SIM2_PIPE_ID=0x23 |
| |
| ############################################################################### |
| #Set the Felica T3T System Code Power state : |
| #This settings will be used when application does not set this parameter |
| #Update Power state as per NCI2.0 |
| DEFAULT_SYS_CODE_PWR_STATE=0x00 |
| |
| ############################################################################### |
| #Maximum SMB transceive wait for response |
| NXP_SMB_TRANSCEIVE_TIMEOUT=2000 |
| ############################################################################### |
| # Firmware file type |
| #.so file 0x01 |
| #.bin file 0x02 |
| NXP_FW_TYPE=0x01 |
| ############################################################################ |
| # Extended APDU length for ISO_DEP |
| ISO_DEP_MAX_TRANSCEIVE=0xFEFF |
| ######################################################################### |
| # Support for Amendment I SEMS specification |
| # Support SEMS Amendment I 0x01 |
| # Support NXP LS client 0x00 |
| NXP_GP_AMD_I_SEMS_SUPPORTED=0x01 |
| ############################################################################### |
| #All eSE terminals shall be match with the /vendor/etc/vintf/manifest.xml file |
| #under android.hardware.secure_element. |
| # The terminal name shall start from 1 |
| # Assign terminal number to each interface based on system config |
| NXP_SPI_SE_TERMINAL_NUM="eSE1" |
| ############################################################################### |
| # Assign terminal number to each interface based on system config |
| #NXP_VISO_SE_TERMINAL_NUM="eSE3" |
| ############################################################################### |
| # Assign terminal number to each interface based on system config |
| NXP_NFC_SE_TERMINAL_NUM="eSE2" |
| ############################################################################### |
| #For static or dynamic dual UICC feature support |
| #Enable static dual uicc feature by setting value 0x00 |
| #Enable dynamic dual uicc feature by setting value 0x01 |
| NXP_DUAL_UICC_ENABLE=0x01 |
| ############################################################################### |
| # Time to wait by DH when NFCC will report eSE Cold Temp Error. |
| # The value is as per the UM and in seconds |
| NXP_SE_COLD_TEMP_ERROR_DELAY=0x05 |
| |
| ############################################################################### |
| # Set configuration optimization decision setting |
| # Enable = 0x01 |
| # Disable = 0x00 |
| NXP_SET_CONFIG_ALWAYS=0x00 |
| |
| ############################################################################### |
| #OffHost ESE route location for MultiSE |
| #ESE = C0 |
| OFFHOST_ROUTE_ESE={C0} |
| |
| ############################################################################### |
| #OffHost UICC route location for MultiSE |
| #UICC1 = 80 |
| OFFHOST_ROUTE_UICC={80} |
| |
| ############################################################################### |
| #T4T NFCEE ENABLE |
| #bit pos 0 = T4T NFCEE Enable |
| #bit pos 6 = T4T NFCEE Contactless write enable |
| #bit pos 7 = Proprietary file enable |
| NXP_T4T_NFCEE_ENABLE=0x01 |
| |
| ############################################################################### |
| #WLC mode |
| #0x00 = if WLC Application running in MW (non-autonomous mode) |
| #0x01 = if WLC Application running in FW (autonomous mode) |
| NXP_WLC_MODE=0x01 |
| |
| ############################################################################### |
| #CORE_SET_CONF_CMD to reset Prop Emvco Flag |
| NXP_PROP_RESET_EMVCO_CMD={20, 02, 05, 01, A0, 44, 01, 00} |
| |
| ############################################################################### |
| #Guard time in ms for the mPOS/SCR module to process the reader start/stop req |
| NXP_RDR_REQ_GUARD_TIME=0 |
| |
| ############################################################################### |
| #MW workaround to enable LPCD when EMVCO polling mode starts and disable |
| #while switching back to NFC Forum mode |
| # 0 --> Disable MW workaround |
| # 1 --> Enable MW workaround |
| # 2 --> Use this option only for FW versions below 1.10.52 |
| NXP_RDR_DISABLE_ENABLE_LPCD=1 |
| |
| ############################################################################### |
| # Firmware patch format, Only 1 and 5 should be set |
| # 0 -> NFC Default |
| # 1 -> EMVCO Default |
| # 3 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = Removal process |
| # 5 -> EMVCO Cert Polling, DISC_IDLE = Removal process , DISC DEACTIVATE = POWER_OFF |
| # 7 -> EMVCO Polling, DISC_IDLE = POWER_OFF, DISC DEACTIVATE = POWER_OFF |
| NFA_CONFIG_FORMAT=1 |
| |
| ################################################################################# |
| # Enable disconnect tag in screen off |
| # Disable 0x00 |
| # Enable 0x01 |
| NXP_DISCONNECT_TAG_IN_SCRN_OFF=0x01 |
| |
| ################################################################################# |
| # Enable wait/delay if RF session is active. |
| # Disable 0x00 |
| # Enable 0x01 |
| NXP_CE_PRIORITY_ENABLED=0x00 |
| |
| ################################################################################# |
| # Core configuration extensions |
| # It includes |
| # Wired mode settings A0ED, A0EE |
| # Tag Detector A040, A041, A043 |
| # Low Power mode A007 |
| # Clock settings A002, A003 |
| # PbF settings A008 |
| # Clock timeout settings A004 |
| # eSE (SVDD) PWR REQ settings A0F2 |
| # Window size A0D8 |
| # DWP Speed A0D5 |
| # How eSE connected to PN553 A012 |
| # UICC2 bit rate A0D1 |
| # SWP1A interface A0D4 |
| # DWP intf behavior config, SVDD Load activated by default if set to 0x31 A037 |
| NXP_CORE_CONF_EXTN={20, 02, 09, 02, |
| A0, EC, 01, 01, |
| A0, ED, 01, 01 |
| } |
| # A0, F2, 01, 01, |
| # A0, 40, 01, 01, |
| # A0, 41, 01, 02, |
| # A0, 43, 01, 04, |
| # A0, 02, 01, 01, |
| # A0, 03, 01, 11, |
| # A0, 07, 01, 03, |
| # A0, 08, 01, 01 |
| # } |
| |
| ############################################################################### |
| # Core configuration settings |
| # Below params are not recommended to add in CONF block. |
| # LA_BIT_FRAME_SDD(0x30) |
| # LA_PLATFORM_CONFIG(0x31) |
| # LA_SEL_INFO(0x32) |
| # LB_SENSB_INFO(0x38) |
| # LF_PROTOCOL(0x50) |
| # NFCC_CONFIG_CONTROL(0x85) |
| |
| NXP_CORE_CONF={ 20, 02, 25, 0B, |
| 28, 01, 00, |
| 21, 01, 00, |
| 33, 04, 01, 02, 03, 04, |
| 54, 01, 06, |
| 5B, 01, 00, |
| 3E, 01, 00, |
| 80, 01, 01, |
| 81, 01, 01, |
| 82, 01, 0E, |
| 18, 01, 01, |
| 68, 01, 01 |
| } |
| ############################################################################### |
| # Enable(0x01) or disable(0x00) non-standard tag reading |
| # Disable Non-standard card read 0x00 |
| # Enable Non-standard card read 0x01 |
| NXP_SUPPORT_NON_STD_CARD=0x00 |
| ################################################################################# |
| # Enable(0x01) or disable(0x00 ) for getting HW Info log over SMB wired |
| # Disable getting HW info log 0x00 |
| # Enable getting HW info log 0x01 |
| NXP_GET_HW_INFO_LOG=0x00 |
| ################################################################################# |
| # Enable(0x01) or disable(0x00) iso dep sak merge |
| # Disable SAK merging 0x00 |
| # Enable SAK merging 0x01 |
| NXP_ISO_DEP_MERGE_SAK=0x01 |
| ################################################################################# |
| # Valid time difference range within for non-standard tag detection from first |
| # Activation fail to next discovery |
| # Note :- 1. This will take effect only when NXP_SUPPORT_NON_STD_CARD is enabled |
| # 2. The number will be multiplied by 100ms by MW. |
| # Default: |
| # Set to 00 if not supported |
| # byte[0] MIFARE_CLASSIC 100ms |
| # byte[1] ISO_DEP 300ms |
| NXP_NON_STD_CARD_TIMEDIFF={01, 03} |
| ################################################################################# |
| # Enable or Disable UICC ETSI support |
| # Disable UICC ETSI support 0 |
| # Enable UICC ETSI support 1 |
| NXP_UICC_ETSI_SUPPORT=0 |
| ################################################################################# |
| # Enable Stop/Start of RF discovery for NFCEE recovery |
| # Disable RF Restart for NFCEE recovery 0 |
| # Enable RF Restart for NFCEE recovery 1 |
| NXP_RESTART_RF_FOR_NFCEE_RECOVERY=1 |
| ################################################################################# |
| |